Axial Detuner Maintenance

of 5
All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.
Document Description
RTA58T-B Maintenance 3146–1/A1 Axial Detuner Dismantling and Assembling Tools: 1 Steel rope with two shackles 1 Roller support 2 Eye bolts M16 94309 94310 Key to Illustrations: 1 2 3 4 5 6 7 8 9 10 11 12 13 Upper part of cylinder Lower part of cylinder Screw Screw Screw Large seal ring Small seal ring Self-locking nut Allen screw Throttling valve Spindle Locking screw Diaphragms 14 15 16 17 18 19 20 21 22 Oil inlet pipe Main bearing cover Crankshaft Main bearing shell Oil drain pipe Upper c
Document Share
Document Tags
Document Transcript
  RTA58T-B Maintenance 3146–1/A1 1 Wärtsilä NSD Switzerland Ltd Key to Illustrations: 1Upper part of cylinder2Lower part of cylinder3Screw4Screw5Screw6Large seal ring7Small seal ring8Self-locking nut9Allen screw10Throttling valve11Spindle12Locking screw13Diaphragms14Oil inlet pipe15Main bearing cover16Crankshaft17Main bearing shell18Oil drain pipe19Upper casing20ELBA (El. balancer)21Screw22Piping for detunermonitoringHLifting tackleREye bolt ools: 1Steel rope with two shackles943091Roller support943102Eye bolts M16When the seal ring 6 or 7 has to be removed from an axial detuner, proceed as follows: –Switch off the bearing oil pump. –Remove the oil drain pipe 18. –Unscrew and remove the oil inlet pipes 14 and the piping for detuner monitoring internal and external from theupper casing 19. –Remove the upper casing 19. 20 A 1819 99.7159 1422Axial Detuner Dismantling and Assembling 1999  Maintenance 3146–1/A1 RTA58T-B 2 Wärtsilä NSD Switzerland Ltd Dismantling  –Remove the oil inlet pipe 14. –Loosen screws 21 and remove the throttling valve 10. –Pull both taper pins locating the upper and lower part of cylinder 1 and 2 by means of the withdrawing devicewhich is part of the standard tools. For this purpose the taper pins have been provided with a thread of M10. –Loosen and remove all the screws 5 and 3 (Fig. ’B’). –Loosen all screws 4 to the upper part of cylinder 1 and pull them out as far as possible. 99.7063 1371251414316217761011 B 2115 Axial Detuner: Dismantling and Assembling 1999  RTA58T-B Maintenance 3146–1/A1 3 Wärtsilä NSD Switzerland Ltd Removal of the upper part of cylinder  –Fasten roller support 94310 to the face of thefree end of the engine as shown in Fig. ’C’. –Screw the two eye bolts ’R’ into the upper partof cylinder 1, then join these by means ofshackles and steel rope 94309 to a liftingtackle. –Using lifting tackle carefully raise upper partof cylinder . Make absolutely sure that the up-per part of cylinder slides out of the sealrings 6 and 7 without jamming , as other-wise the seal rings risk being damaged. C 99.7064 I 194309R9431094310 I 94309R161567H Axial Detuner: Dismantling and Assembling 1999  Maintenance 3146–1/A1 RTA58T-B 4 Wärtsilä NSD Switzerland Ltd 6 (7)98 Removal of the seal rings Should the two-part seal rings 6 and 7 have to bereplaced, loosen first self-locking nut 8 and removeallen screw 9. The sealing rings can then be turnedout of their grooves in the lower part of cylinder 2without any problems. Checking the throttling valve When overhauling the axial detuner check also thecondition of throttling valve 10. The spindle positionhas been locked by locking screw 12 and a lockingplate. Changing the position of the throttlingvalve is forbidden. For pre-setting the spindle 11 has to be turned backby about four turns starting from the closed position.This adjustment must be verified on the basis ofvibration measurements during sea trial; otherwisethe spindle must be readjusted. The final adjustmenthas to be engraved on the name plate fitted to theupper part of the cylinder 1. 99.7050 DE 11131211 X  Should it become necessary to unscrew or replace a spindle for any reason, then the distance ’x’ must be measuredfirst (Fig. E’). The spindle has to be adjusted to the same distance on reassembling.The spindle must not be turned back by more than 17 ½ turns , that corresponds to a stroke ofx=35 mm.When the above check brings to light any defect of throttling valve 10 then diaphragms 13 screwed into the throttlingvalve must also be checked for possible damage and replaced if necessary.The engine must not be operated with the spindle removed! Axial Detuner: Dismantling and Assembling 1999 Remark Attention 
We Need Your Support
Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

Thanks to everyone for your continued support.

No, Thanks

We need your sign to support Project to invent "SMART AND CONTROLLABLE REFLECTIVE BALLOONS" to cover the Sun and Save Our Earth.

More details...

Sign Now!

We are very appreciated for your Prompt Action!