Ip Address Understanding

Please download to get full document.

View again

of 3
18 views
PDF
All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.
Document Description
6.8.1: Skills Integration Challenge-Planning Subnets and Configuring IP Addresses Topology Diagram Addressing Table Device R1-ISP R2Central PC 1A PC 1B Eagle Server Interface Fa0/0 S0/0/0 Fa0/0 S0/0/0 NIC NIC NIC IP Address Subnet Mask Default Gateway N/A N/A N/A N/A All contents are Copyright © 1992–2007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 1 of 3 CCNA Exploration Network Fundamentals: Addressing the Network - IPv4 6.8.1: Skills Inte
Document Share
Documents Related
Document Tags
Document Transcript
    6.8.1: Skills Integration Challenge-Planning Subnets andConfiguring IP Addresses Topology DiagramAddressing TableDevice Interface IP Address Subnet MaskDefaultGateway Fa0/0 N/A R1-ISPS0/0/0 N/A Fa0/0 N/A R2-CentralS0/0/0 N/A PC 1ANICPC 1BNICEagleServerNIC All contents are Copyright © 1992–2007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 1 of 3  CCNA ExplorationNetwork Fundamentals:Addressing the Network - IPv4 6.8.1: Skills Integration Challenge-Planning Subnets and Configuring IP Addresses Learning Objectives ã IP Subnet Planning o Practice your subnetting skills. ã Build the Network. o Connect devices with Ethernet and serial cables. ã Configure the network. o Apply your subnetting scheme to server, PCs, and router interfaces; configureservices and static routing. ã Test the network. o Using ping, trace, web traffic, Inspect tool Background You have been asked to implement the standard lab topology, but with a new IP addressingscheme. You will use many of the skills you have learned to this point in the course. Task 1: IP Subnet Planning You have been given an IP address block of 192.168.23.0 /24. You must provide for existingnetworks as well as future growth.Subnet assignments are: ã 1st subnet, existing student LAN (off of router R2-Central), up to 60 hosts; ã 2nd subnet, future student LAN, up to 28 hosts; ã 3rd subnet, existing ISP LAN, up to 12 hosts; ã 4th subnet, future ISP LAN, up to 8 hosts; ã 5th subnet, existing WAN, point-to-point link; ã 6th subnet, future WAN, point-to-point link; ã 7th subnet, future WAN, point-to-point link.Interface IP addresses: ã For the server, configure the second highest usable IP address on the existing ISP LANsubnet. ã For R1-ISP's Fa0/0 interface, configure the highest usable IP address on the existing ISPLAN subnet. ã For R1-ISP's S0/0/0 interface, configure the highest usable address on the existing WANsubnet. ã For R2-Central's S0/0/0 interface, use the lowest usable address on the existing WANsubnet. ã For R2-Central's Fa0/0 interface, use the highest usable address on the existing studentLAN subnet. ã For hosts 1A and 1B, use the first 2 IP addresses (two lowest usable addresses) on theexisting student LAN subnet. All contents are Copyright © 1992–2007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 2 of 3  CCNA ExplorationNetwork Fundamentals:Addressing the Network - IPv4 6.8.1: Skills Integration Challenge-Planning Subnets and Configuring IP Addresses Additional configurations: ã For PCs 1A and 1B, in addition to IP configuration, configure them to use DNS services. ã For the server, enable DNS services, use the domain name eagle-server.example.com,and enable HTTP services. ã For R1-ISP router serial interface, you will need to set the clock rate (a timing mechanismrequired on the DCE end of serial links) to 64000. ã No clock rate is needed on the DTE side, in this case R2-Central's serial interface. Task 2: Finish Building the Network in Packet Tracer. Add cables where missing. ã Connect a serial DCE cable to R1-ISP S0/0/0, with the other end to R2-Central S0/0/0. ã Connect PC 1A to the first FastEthernet port on switch S1-Central. ã Connect PC 1B to the second FastEthernet port on switch S1-Central. ã Connect interface Fa0/0 on router R2-Central to the highest FastEthernet port on switchS1-Central. ã For all devices, make sure the power is on to the device and the interfaces. Task 3: Configure the Network. You will need to configure the server, both routers, and the two PCs. You will not need toconfigure the switch nor do you need the IOS CLI to configure the routers. Part of the routerconfiguration has already been done for you: all you must do is configure the static routes and theinterfaces via the GUI. The static route on R1-ISP should point to the existing student LAN subnetvia R2-Central's serial interface IP address; the static route on R2-Central should be a defaultstatic route which points via R1-ISP's serial interface IP address. These procedures wereexplained in the Chapter 5 Skills Integration Challenge. Task 4: Test the Network. Use ping, trace, web traffic, and the Inspect tool. Trace packet flow in simulation mode, withHTTP, DNS, TCP, UDP, and ICMP viewable, to test your understanding of how the network isoperating. Reflection Reflect upon how much you have learned so far! Practicing IP subnetting skills and networkingbuilding, configuration and testing skills will serve you well throughout your networking courses. All contents are Copyright © 1992–2007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 3 of 3
We Need Your Support
Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

Thanks to everyone for your continued support.

No, Thanks
SAVE OUR EARTH

We need your sign to support Project to invent "SMART AND CONTROLLABLE REFLECTIVE BALLOONS" to cover the Sun and Save Our Earth.

More details...

Sign Now!

We are very appreciated for your Prompt Action!

x