Pilot II Data 1110

of 4
11 views
PDF
All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.
Document Description
Technical Data Pilot II Product description Pilot II is an alkyd based topcoat for both exterior and interior use. This product is part of a complete system which is certified not to spread surface flames. Pilot II bases are intermediates and need to be processed before use. Recommended use Topcoat in a traditional alkyd system suitable for steel and woodwork. Good weather and colour stability. Good hiding power. Film thickness and spreading rate Minimum Film thickness, dry (µm) Film thickne
Document Share
Document Tags
Document Transcript
  Pilot IIPage 1 of 4 Technical Data Pilot II Product description Pilot II is an alkyd based topcoat for both exterior and interior use. This product is part of a complete system which iscertified not to spread surface flames. Pilot II bases are intermediates and need to be processed before use. Recommended use Topcoat in a traditional alkyd system suitable for steel and woodwork. Good weather and colour stability. Good hidingpower. Film thickness and spreading rate MinimumMaximumTypicalFilm thickness, dry (µm) 305040 Film thickness, wet (µm) 6010585 Theoretical spreading rate (m²/l) 169,612 Comments Hong Kong rules: Category of paints - Marine maintenance coatings; VOC 400 gms/ltr HK EPD method (Ready touse); Exempt compound - N/A; Specific gravity: 1.04;Both VOC and Specific gravity values provided are typical values, subject to changes whendifferent colour involved. Approvals APAS approved to specification 2922.  Pilot IIPage 2 of 4 Physical properties Colour According to colour card and Multicolor tinting system (MCI) Solids (vol %)* 48 ± 2 Flash point 36ºC ± 2 (Setaflash) VOC 410 gms/ltr UK-PG6/23(97). Appendix 3 Gloss Glossy Gloss retention Good Water resistance Limited Abrasion resistance Fair Flexibility Good*Measured according to ISO 3233:1998 (E) Surface preparation All surfaces should be clean, dry and free from contamination. The surface should be assessed and treated inaccordance with ISO 8504. Coated surfaces Clean, dry and undamaged compatible primer. Please contact your local Jotun office for more information. Other surfaces The coating may be used on other substrates. Please contact your local Jotun office for more information. Condition during application The temperature of the substrate should be minimum 3ºC above the dew point of the air, temperature and relativehumidity measured in the vicinity of the substrate. Good ventilation is usually required in confined areas to ensurecorrect drying.  Pilot IIPage 3 of 4 Application methods Spray Use airless spray or conventional spray Brush Recommended for stripe coating and small areas, care must be taken to achieve the specified dryfilm thickness. Roller May be used. However when using roller application care must be taken to apply sufficient material inorder to achieve the specified dry film thickness. Application data  Mixing ratio (volume) Single pack. Thinner/Cleaner Jotun Thinner No. 2 Guiding data airless sprayPressure at nozzle 15 MPa (150 kp/cm², 2100 psi) Nozzle tip 0.38 - 0.53 mm (0.015 - 0.021 ) Spray angle 40 - 80° Filter Check to ensure that filters are clean. Drying time Drying times are generally related to air circulation, temperature, film thickness and number of coats, and will beaffected correspondingly. The figures given in the table are typical with:* Good ventilation (Outdoor exposure or free circulation of air)* Typical film thickness* One coat on top of inert substrate Substrate temperature5°C10°C23°C40°CSurface dry 5 h4 h3 h1 h Through dry 25 h14 h7 h3 h Dry to recoat, minimum 36 h18 h16 h12 h Dry to recoat, maximum 1 1.The surface should be dry and free from any contamination prior to application of the subsequent coat.The given data must be considered as guidelines only. The actual drying time/times before recoating may be shorter orlonger, depending on film thickness, ventilation, humidity, underlying paint system, requirement for early handling andmechanical strength etc. A complete system can be described on a system sheet, where all parameters and specialconditions could be included. Typical paint system Alkydprimer or Pilot Primer2 x 40 µm(Dry Film Thickness) Pilot II1 x 40 µm(Dry Film Thickness)Note 1: To obtain full coverage an extra coat may be necessary, especially for signal colours in red, orange and yellow. Note 2: Pilot II is not suitable for direct application to zinc rich primers or galvanised surfaces or alkaline substratessuch as concrete.  Pilot IIPage 4 of 4 Other systems may be specified, depending on area of use Storage The product must be stored in accordance with national regulations. Storage conditions are to keep the containers in adry, cool, well ventilated space and away from source of heat and ignition. Containers must be kept tightly closed. Handling Handle with care. Stir well before use. Packing size 5 litre container or 20 litre container Health and safety Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do notbreathe or inhale mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable cleanser,soap and water. Eyes should be well flushed with water and medical attention sought immediately. For detailed information on the health and safety hazards and precautions for use of this product, we refer tothe Material Safety Data Sheet.DISCLAIMER The information in this data sheet is given to the best of our knowledge based on laboratory testing and practicalexperience. However, as the product can be used under conditions beyond our control, we can only guarantee thequality of the product itself. We also reserve the right to change the given data without notice. Minor product variationsmay be implemented in order to comply with local requirements.If there is any inconsistency in the text the English (UK) version will prevail. Jotun is a World Wide company with factories, sales offices and stocks in more than 50 countries. For your nearest local Jotun addressplease contact the nearest regional office or visit our website at www.jotun.com ISSUED 26 NOVEMBER 2010 BY JOTUNTHIS DATA SHEET SUPERSEDES THOSE PREVIOUSLY ISSUED
We Need Your Support
Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

Thanks to everyone for your continued support.

No, Thanks
SAVE OUR EARTH

We need your sign to support Project to invent "SMART AND CONTROLLABLE REFLECTIVE BALLOONS" to cover the Sun and Save Our Earth.

More details...

Sign Now!

We are very appreciated for your Prompt Action!

x